Release contains:
File | Version |
---|---|
HeliumPolish.exe | 5.6.91.1 |
report.dll | 2.10.34.1 |
BrilRecon.dll | 1.1.24.1 |
ikov.dll | 1.1.3.9 (not changed) |
Report templates | 2017-04-05 |
In this version we made the following changes:
Model building
Algorithm for building girdle for Octagon cut is improved (Please use Brilliant method for Octagon cut).
Previous release | Current release |
---|---|
Reports
Corrected mass in reports
Corrected mass is now displayed in the reports as two values, namely, with 2-digit and 4-digit precision.
Please note that CORRECTED_MASS_2 and WEIGHT_CT bookmarks are not affected by digit precision option, so it has 2 digit precision in any case.
Reported in | Section | Units | Bookmarks |
---|---|---|---|
| Top |
|
|
CORRECTED_MASS_4 (4 digits, new bookmark) |
Lower Facet Length for Cushion
Lower Facet Length parameter is added for Cushion cuts.
It is defined as the projected distance from the junction of the main pavilion facets to the corresponding side of the girdle, and reported separately for all four sides.
Reported in | Section | Values | Units | Bookmarks |
---|---|---|---|---|
Full Report for Cushion | Main Parameters | Avg, Min, Max, Dev at each direction | Both %(diameter) and mm |
|
Detailed Parameters | Individual values (2 at each direction) | Both %(diameter) and mm | LOWER_FACET_LENGTH_0_1, LOWER_FACET_LENGTH_0_2, LOWER_FACET_LENGTH_90_1, LOWER_FACET_LENGTH_90_2, LOWER_FACET_LENGTH_180_1, LOWER_FACET_LENGTH_180_2, LOWER_FACET_LENGTH_270_1, LOWER_FACET_LENGTH_270_2 |
Crown Main Width and Crown Main Length facets for Cushion
For a non-standard Cushion cut having four Crown Main Width and four Crown Main Length facets, all four individual measurements for their slopes, azimuths, and heights are now reported.
Reported in | Section | Values | Units | Bookmarks |
---|---|---|---|---|
Full Report for Cushion | Detailed Parameters | Individual values #3, 4 | ° | CRN_MAIN_WIDTH_ANGLE_DEG_3, CRN_MAIN_WIDTH_ANGLE_DEG_4, CRN_MAIN_WIDTH_AZIMUTH_DEG_3, CRN_MAIN_WIDTH_AZIMUTH_DEG_4, CRN_MAIN_LENGTH_ANGLE_DEG_3, CRN_MAIN_LENGTH_ANGLE_DEG_4, CRN_MAIN_LENGTH_AZIMUTH_DEG_3, CRN_MAIN_LENGTH_AZIMUTH_DEG_4, |
Pavilion Wing Facets
Algorithm for detection wing facets is improved:
Previous release | Current Release |
---|---|
Facet type detection for Round Fancies
Algorithm for facet type detection is improved for Round Fancies:
Previous release | Current Release |
---|---|
Girdle internal angle for Step Cut
Algorithm for girdle internal angle calculation is improved.
Previous release | Current Release |
---|---|
Pavilion and crown facets type recognition on RBC
Pavilion and crown facets type bad recognition on RBC is improved:
Previous release | Current Release |
---|---|
Radiant and square radiant facet height
Radiant and square radiant facet height measurement is changed:
- In previous release facet height was measured as distance from table to lowest point of facet.
- In current release it is measured as distance from highest point to lowest point of factet.
Bug Fixes
- Table edge calculation in a Round brilliant with extra facets is fixed.
- Girdle height calculation for stones with extra girdle facets is fixed.
- Girdle bezel height statistics for 10x brilliant is fixed.
- "GIA heights" option does not affect on avarage diameter calculation.