...
Panel | ||||||
---|---|---|---|---|---|---|
| ||||||
|
Algorithm "18. Single (Recut)" for Aligning with Blocked Facets
After scanning a blocked diamond, an operator may run the allocation algorithms to check the available polishing options. As in some cases we try to optimize solutions by running the asymmetric Smart Recut allocation, it is better to have a solution which is better aligned with the previously blocked facets. When we run the Smart Recut on such a solution, we may obtain the final solution with a larger mass. The new "18. Single (Recut)" algorithm allows building solutions aligned to the already blocked facets. At least one of the solutions produced by the algorithm is normally aligned to the already blocked facets of a scanned semipolished stone.
...
Multimedia | ||||
---|---|---|---|---|
|
Galahad Mode - Manual Selection of Initial Facet
In Galahad Mode, for the selected step it is now possible to manually select the initial facet different from the one automatically calculated by the system. Once manually set, the initial facet can then at any moment be reset to the default one.
G1 Galahad - Reference Line and Safe Line
In G1 Galahad mode, the reference line is now calculated only once for the entire polishing process (previously it was calculated for each stage separately). Also, the safe line is calculated which is the limit of safe polishing, i.e. each big facet, with the correct facet angles, can be safely polished down to the safe line without risk of damaging the future brilliant. For the crown, the reference line is displayed by a bold orange line, safe line - by a thin dotted orange line. On the left panel, on mouse over the Distance to reference line parameter, the tooltip is displayed with the information about reference and safe lines.
...
Note |
---|
Note that if the "Girdle" or "Table" stages are included in the process, the distance to the reference line is recalculated for all other stages. |
Rough Export
The new "Rough Export" feature is added. This allows exporting a rough model (in most cases this will be semipolished stones) along with the set of solutions created for it. You can select one of two options:
- Rough Export - all solutions - the main scan and all the solutions will be exported
- Rough Export - active solution - the main scan and the selected solution will be exported
Recut - Deleting Inclusions
Now you can delete existing inclusions. To delete the inclusion, on the left panel, in the Plans & Scans mode, in the Inclusions section, right-click the inclusion you want to delete, from the context menu, select Delete Inclusion.
...
You can delete several inclusions at once. To do so, select inclusions clicking their names holding the CTRL or SHIFT keys, then use the context or pop-up menu.
Appraiser List Favorites
In the list of appraisers, now you can mark some appraisers as favorites: these marked appraisers will be shown as a "short list" displayed by default. The full list is available on clicking show all. To mark the appraiser as a favorite, click the star mark - it becomes highlighted. To remove the appraiser from favorites, click the start again to deselect .
Custom Coloring Improvement
The colors for the Facet Marking of the Custom Report have been changed. The overview of the updated coloring is presented in the video.
Multimedia | ||||
---|---|---|---|---|
|
G1 Panel Improvements
On the Galahad 1 (G1) panel, in all context menus now the icons are displayed which makes working with menus more convenient.
...
When trying to delete the stage, now the confirmation dialog is displayed. There you can confirm deletion of the stage or cancel deletion if you initiated it by mistake.
Support of Scanning without Synchronization Cable
Now the scanning without synchronization cable is supported. On start, the system checks the synchronization cable availability. If a cable present, the scanning uses synchronization. If the cable is not found, scanning still continues - without synchronization.
Info |
---|
Note that scanning without synchronization is slower. It is recommended to update the hardware to the newer version (HP_SMC board). |
Galahad Compass - Big Step, Using Same Direction
In Galahad Compass - if a step is separated into sub-steps ("Bid Step" feature), after the direction and zero is set for the first sub-step, the system will automatically use the same direction for all following sub-steps. Previously, an operator should have defined the direction manually for each sub-step. Note that if you need to change the direction manually, you still have the ability to do that: use the Clear button and then set the new direction in a usual way.
New Report Parameters for Cuttings: Emerald, Princess, Heart, Oval, Pear
New parameters for the report were added for different cuttings.
...
Expand | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
"MyRound | GIA Facetware + MyRound" Appraiser - Dual Grade Display
Now, for the "MyRound | GIA Facetware + MyRound" appraiser, when GIA Facetware and MyRound grades differ, both grades are displayed in the solution list simultaneously.
Info |
---|
Grades are displayed in GIA Facetware-MyRound format, for example, "VG-GD" means that GIA Facetware grade is "VG" and MyRound is "GD". |
Calculation of Girdle Thickness, Crown Height and Pavilion Depth - Reverse to Considering Extra Facets only for Girdle Thickness
For the previous version (4.6.21), the Crown Height and Pavilion Depth were calculated taking into account the presented extra facets. Using this calculation method led to estimation grades in HP Oxygen lower than could be actually obtained from GIA. Thus the decision has been made to reverse to the calculation method used before v.4.6.21: the Crown Height and Pavilion Depth calculation is based on a virtual model with excluded extra facets (that is, does not take extra facets into account) and the calculation of the Girdle Thickness considers the extra facets.
Detailed information about these parameters can be found in the HP Oxygen documentation: Girdle Thickness, Crown Height and Crown Height Symm, Pavilion depthDepth.