...

1. Table Edge Junctions are now calculated for all cutting types. Corresponding bookmarks were implemented and added to report templates:

   RBC	Oval	Marquise
   Image Modified	Image Modified	Image Modified

   Expand

   TABLE_EDGE_JUNCTION_MM_MIN TABLE_EDGE_JUNCTION_MM_MAX TABLE_EDGE_JUNCTION_MM_AVG TABLE_EDGE_JUNCTION_MM_DEV TABLE_EDGE_JUNCTION_MM_1..8 TABLE_EDGE_JUNCTION_PC_MIN TABLE_EDGE_JUNCTION_PC_MAX TABLE_EDGE_JUNCTION_PC_AVG TABLE_EDGE_JUNCTION_PC_DEV TABLE_EDGE_JUNCTION_PC_1..8 TABLE_EDGE_MM_MIN TABLE_EDGE_MM_MAX TABLE_EDGE_MM_AVG TABLE_EDGE_MM_DEV TABLE_EDGE_MM_1..8 TABLE_EDGE_PC_MIN TABLE_EDGE_PC_MAX TABLE_EDGE_PC_AVG TABLE_EDGE_PC_DEV TABLE_EDGE_PC_1..8 MODEL_TABLE_EDGE_MM_MIN MODEL_TABLE_EDGE_MM_MAX MODEL_TABLE_EDGE_MM_AVG MODEL_TABLE_EDGE_MM_DEV MODEL_TABLE_EDGE_MM_1..8 MODEL_TABLE_EDGE_PC_MIN MODEL_TABLE_EDGE_PC_MAX MODEL_TABLE_EDGE_PC_AVG MODEL_TABLE_EDGE_PC_DEV MODEL_TABLE_EDGE_PC_1..8

2. Fixed an outstanding issue that caused randomly missing images in RTF Polish reports, most notably in Full reports.
   All images should now be successfully generated every time, given a correct and valid template.
   
   
3. Completely re-worked the Comparative report model matching algorithms for better all-round results on all cuttings.
   
   
4. Improved matching of Culet, Cavity, Knife, Girdle facets in Comparative report for non-trivial cases.
   
   
5. GIA Rounded parameter values are added to the Standard Report for RBC. Available with GIA Facetware appraiser.
   
   
   
   
6. Added mm values of most important parameters to Standard Report. % values are still available in the same column.
   
   
   
   
7. Crown Height and Pavilion Height interactive values are now available in Standard Report for RBC and AnyCut:
   
   
   
   When the parameter is selected, you will see a dot located on the upper or lower girdle line at the point where the corresponding measurement was made.
   You can then align the selected stone element to the scanner door by pressing the "Rotate to door: Selected Facet" button.
   
   Clicking on a selected parameter once more will deselect it.
   
   
8. Precision setting in Standard Report now affects all relevant parameters.
   
   
9. Improved Star facets detection on rounded fancies.
   
   

10. Improved facet type detection on RBC.

...

1. It is now possible to run SmartRecut algorithm on Copy cuttings.
   
   

2. Oval Sweetline parameter is added to the SmartRecut Oval presets.
   
   Presently the optimal line is defined as the line with negative slope 1:3 passing through the point with CrownAngle = 36.5 and PavilionAngle = 38.5.
   Image Added
   SweetLine is currently not revealed in MyAppraiser and can be managed only via presets. The default value (There default value of Oval SweetLine in presets is 3.5) or greater value means that the allowed stripe covers the entire rectangle of individual limitations on CrownAngle and PavilionAngle, so in effect no new limitations are imposed. Smaller values of SweetLine would cut out a stripe from the rectangle, potentially enabling the search for favorable solutions over a wide range of parameters. Previously this area could only be covered by a series of smaller rectangles, that is, by running the search multiple times with extremely tightened CrownAngle and PavilionAngle, each time covering a small portion of the stripe. Sweetline offers a less time-consuming alternative to this approach
   Image Removed°. This value determines zone/stripe by PavilionAngle, upper and lower edges of this zone/stripe pass in 3.5° by PavilionAngle from sweetline as shown on graphics above. i.e. zone is stripe with "width" of 7 degrees by PavilionAngle. Green frame "EX" shows current intervals of MyOval appraiser of EX group for Crown Angle (from 31° to 40°) and Pavilion angle (from 37.5° to 40.5°) which are set by operator in AppraiserEditor panel.
   Image Added

   Sweetline value can be decreased to smaller value to get final solutions with CrownAngle/PavilionAngle more close to Optimal Line.  For example, if operator decrease sweetline value to 1.75° (zone is shown on picture below) then final solutions will contain CrownAngle and PavilionAngle values in the limits of zone Sweetline 1.75°, more close to optimal line than default value 3.5°. This "tightening" results in better optical performance but could results in worse weight of plan diamond also. Operator can adjust sweetline value to reach optimal ratio "optical performance/weight of plan diamond.

   Image Added 

3. MyOval appraiser and presets are improved to achieve resulting solutions with better optical performance and symmetry.
   
   
4. MyRound appraiser and presets were improved to better suite GIA Facetware limits. 
   Two SmartRecut presets still retain relaxed intervals to showcase possible maximum mass gains while exceeding some of the MyAppraiser target group limits.
   
   
5. SmartRecut algorithm is improved to achieve higher EX target group result rate.

...

1. Manual Acceleration setting GUI is now available:

   Image Modified

   Image Modified

   You can choose acceleration setting from ten options with 1 being the slowest and 10 being the fastest.
   For this setting to be available you have to update the HPODrivers.ini file.

...

1. 06. Semicut (final) algorithm now properly considers model orientation so that Recut solutions are always oriented correctly in relation to the semi-cut stone.
   
   06-Semicut-Final_Sample.oxgz

   Previous versions	HPO 3.22.41
   Image Modified	Image Modified

Bugfixes

1. You can now run Recut after importing a model from an MME file.
2. Multiple small bugs fixed.