Release contains:

In this version we made the following changes:

Model building

1. Model building using Sample algorithm for Round Brilliant 10x cut is improved.

   Before	After
   Model used: RBC10x_ModelBuildingImprovement.Mmd

Reports

1. Model can be exported to ASCII format in standard orientation (that is, oriented the same way as in the polish reports).
   To enable ASCII export upon scanning or rebuilding, go to Report - Report options and check the following check boxes:

   1. ascii:report basis if you want to export models in standard orientation (same as in the reports).
      

   2. ascii if you want to export models in the same orientation as scanned.
      

   If you checked both options, make sure the files are saved into different folders.

2. Painting parameters have their sign reversed, so as to match the GIA definition.
   
   

   Note that the Dev values and the measurements in notches are defined as absolute values, hence their sign is not changed.

Bugfixes

1. Bugs that caused incorrect drawing of the girdle 2D graph and occasional negative girdle valley height values for stones with cavernous girdles are fixed.
   

    Originally noticed in the email from Janak on August 27:

   From: "Janak Mistry" <janak@lexus-com.com>
   Subject: FW: Negative girdle hill
   Date: 27 August 2016 at 14:46:50 GMT+3
   To: "Sergey Sivovolenko" <sivovolenko@octonus.com>, <Savrasov@octonus.com>
   Cc: <nilesh@lexus-com.com>

   Dear Sergey,

   Please find this project.
   It has concavity in the girdle.
   
   

   Probably because of this cavity in girdle, the girdle is measured as with negative value in one of the location.
   

   What should be the correct value of the girdle thickness at this location?

   Regards,
   Janak

   
   

2. The following bugs in the Round brilliant 10x report are fixed:

   1. Only 4 out of 5 Table width values were shown.
      

       Originally noticed in the email from Nilesh on August 17:

      From: "Nilesh Vaghmashi" <nilesh@lexus-com.com>
      Subject: 10 faceted H&A Round_Semistage(OnlyPAVILION FULLY FINISHED-CROWN10Facet) Model improvement from Pavilion Side+Table 5 % missing.
      Date: 17 August 2016 at 13:36:30 GMT+3
      To: <savrasov@octonus.com>
      Cc: <sivovolenko@octonus.com>, <janak@lexus-com.com>, "Utpal Mistry" <utpal@lexus-com.com>, <kamal@lexus-com.com>

      Dear Sergey,

      As discussed with you please find attached 3 example of 10 Faceted Round in semi stage (Only Pavilion finished and crown 8 facet).

      As we discussed we have two query.

      1. Model improvement from Pavilion side (I have also attached .srn file for your reference).
      2. Table 5 % missing in report.

      

      
      

   2. Only 8 out of 10 values of Crown height bone and Girdle height bone were shown.
      

       Originally noticed in the email from Nilesh on July 30:

      From: Nilesh Vaghmashi nilesh@lexus-com.com
      Sent: Saturday, July 30, 2016 12:26 PM
      To: 'Janak Mistry' <janak@lexus-com.com>; 'Yaroslav Alexandrov' <alexandrov@octonus.com>; 'Utpal@Lexus-Com. Com' <utpal@lexus-com.com>; kamal@lexus-com.com
      Cc: 'Sergey Sivovolenko' <sivovolenko@octonus.com>; 'Sergey Savrasov' <savrasov@octonus.com>; 'Alexander Shevchenko' <shevchenko@octonus.com>
      Subject: RE: Helium Polish: version 5.6.88.1, report.dll version 2.9.7.1, report templates dd 12.07.2016

      During testing of 10 faceted H&A Round, I found one mmd in which below yellow highlighted data missing.
      

      I also attached Illustrated report.

      Kindly look into this.